P.O. BOX 717 THEODORE, ALABAMA 36590 -0717 PHONE (251) 443-6110 FAX (251) 408-0410
PRODUCT DATA
PRODUCT
DESCRIPTION
TYPICAL USES
PRODUCT
ADVANTAGES
50
PHYSICAL
CONSTANTS
GLOSS
COLORS
APPLICATION
SHIPPING &
STORAGE
SPEEDECK?
Floor and Deck Enamel
50-series
Polyurethane Modified Alkyd
A general purpose interior/exterior high gloss polyurethane modified alkyd enamel.
Lead and chromate free.
For industrial, commercial, residential and marine use including machinery, piping, floors,
decks, structural steel, marine vessels, storage tank exteriors and power plant equipment.
For coating properly prepared steel, galvanized steel, aluminum, masonry and wood surfaces.
SPEEDECK Floor and Deck Enamel offers excellent protection against weather and
abrasion in exposures including mild industrial and marine environments. Good color and
gloss retention on exterior exposures. Excellent abrasion resistance to withstand repeated
traffic. Heat resistant up to 250oF. Lead and chromate free.
Available in 12 standard colors as shown on color card and a wide range of colors produced
from tint bases using the Color Studio System. Refer to Color Studio System for color
selection.
High gloss
Nonvolatile - By weight - 62.9 + 1.0% Average*
By volume -48.4 + 1.0% Average*
VOC (Calculated) - 3.35 lbs./gal. Average*
(excluding water) 400 grams/liter Average*
Flash Point - > 101oF (Setaflash)
Weight per gallon - 9.0 + 0.2 lbs. Average*
*Varies with color.
Recommended Film Thickness - 2.0 mils dry, 4.1 mils wet
Theoretical Coverage @ 2.0 mils dry - 388 sq. ft./gal.
Method - Brush, roll, conventional or airless spray.
Thinner - Thinning is not recommended
Dry time @ 75oF - To touch - 4 hours
To handle - 6 hours
To recoat - 24 hours
Consists of - 1 Gallon Unit 5 Gallon Unit
Unit Shipping Weight 10 lbs. 48 lbs.
Shelf Life - 12 months minimum from date of manufacture when maintained in protected
storage @ 40-100oF (subject to reinspection thereafter).
APPLICATION INSTRUCTIONS
Consult your Mobile Paint Representative for the protective
coating system best suited for your requirements.
Limitations: Apply in good weather when air and surface
temperature are above 35oF and surface temperature is at
least 5oF above the dew point. For optimum application
properties, material should be between 70 to 100oF prior to
mixing and application. Maintain unmixed material in
closed containers in protected storage at 40 - 100oF.
Surface Preparation: Good surface preparation is essential
to a satisfactory coating system. Surfaces to be coated
should be clean and dry. Remove all oil, grease, mildew,
or other contamination by solvent or detergent cleaning or
other effective means.
New or Unfinished Surfaces: Wood: Remove sap with
mineral spirits. Sand Smooth. Exterior,prime with SPEEDECK?.
Interior, prime with SPEEDECK or COVENTRY Wood
Sealer 19-8. Ferrous Metal: For best performance, application
to abrasive blasted steel is recommended. "Commercial
Blast Cleaning" (SSPC-SP6) is recommended as minimum.
Proper blast media and blasting equipment shall be used to
produce and average profile depth of 1.5 mils minimum. Do not
reuse abrasive media. Remove blasting dust and grit from
surfaces before painting. Blasted surfaces should be coated
within 8 hours after blasting or before rusting or other contamination
of the surface occurs. If blasting is not feasible, remove
rust by "Hand or Power Tool Cleaning" (SSPC-SP2 or-SP3).
Prime with RUS-KIL Primer 10-series. Galvanized Metal:
Remove oil and prime with Vinyl Wash Primer 9-48. Concrete
Block: Must be clean, dry and thoroughly cured. Fill pores with
Bloc-FilTM 60-7 or for high humidity exposures.Concrete: Must
be cured, dry and clean. Allow a minimum of 30 days cure time
before coating. (1) "Brush Blast Cleaning" (SSPC-SP7) will
remove efflorescence, laitance and other foreign matter and
roughen the surface for proper adhesion. Remove all dust
before coating. (2) "Acid Etching"-surface must be clean,
cured and free from oil, grease, dirt, curing compounds, chalk
or previously applied coatings. Etch with a solution of 1 part
Muriatic Acid to 2 parts water. Apply by brush or spray to wet
all concrete surfaces to be coated thoroughly. After bubbling
ceases (10-15 minutes) wash surface and scrub with a stiff
brush. Rinse thoroughly with water to remove all traces of acid
and residue. Allow to dry before coating. Aluminum: Clean
thoroughly and etch with a phosphoric acid based cleaning
solution. Rinse well and allow to dry. Prime with RUS-KIL?
Primer 10-series.
Previously Painted Surfaces: Repair all damaged areas.
Remove gloss from previous paint by sanding or Brush
Blasting (SSPC-SP7). Remove rust, corrosion products,
heavy chalk and loose or peeling paint by Hand or Power
Tool Cleaning (SSPC-SP2 or -SP3). Spot prime any bare
areas as in new work above. If doubt exists concerning
compatibility of this coating with the previous system, apply
coating to a representative area (25 square feet
minimum) and allow to cure and age several weeks. Then
inspect for adhesion failure, wrinkling, lifting, blistering or
any other sign of incompatibility. If there are no signs,
coating work can proceed.
Tinting: Color Studio Tint Bases provide hundreds of color
possibilities and should be used only after the addition of
the proper amount of Color Studio colorant. These tint
bases may be short filled to allow for the addition of
colorant. Actual coverage will depend on the amount of
colorant added and should be taken into consideration
when ordering. Some colors may require more than one
coat for complete hiding.
Mixing: This is a one component coating. Always mix
thoroughly with a power agitator before application.
Thinning: This product is supplied at the proper application
viscosity. Thinning is not recommended. See
cleanup paragraph for cleanup thinner.
Application: Apply by brush, roller or conventional or
airless spray. Roller application may require special care
to prevent bubbling and more than one coat to obtain
proper film thickness. Apply at 4.1 mils wet film thickness
which will yield 2.0 mils dry film thickness.
Equipment: Brush - Use a good quality bristle brush.
Roller - All purpose, good quality roller with 3/8" nap
maximum. Conventional spray - For suction feed, use
DeVilbiss MBC gun with E tip and needle and 30 air cap or
equivalent at 40-45 psi atomizing pressure. For pressure
feed, use DeVilbiss MBC gun with E tip and needle and 704
air cap or equivalent at 40-45 psi atomizing pressure and 5-
8 psi fluid pressure, 3/8" ID material hose, double regulated
pressure tank with oil and moisture separator. Airless
Spray - Minimum of 28:1 ratio pump, .011"-.013" tip, 1/4"
ID material hose.
Cleanup: Clean all equipment immediately after use with
MoPaxOl 75-1 or mineral spirits. Completely flush all
spray equipment with either of these solvents. Occasional
flushing of spray equipment during the course of the working
day helps prevent buildup and possible clogging.
Safety: Safe storage, handling and use dictate that adequate
health and safety precautions be observed with this
product and any recommended thinners. User is specifically
directed to consult the current Material Safety Data
Sheet for this product as well as precautions contained on
product labeling.
Notice: The technical data contained herein are true and
accurate to the best of our knowledge. All products are
offered and sold subject to Mobile Paint Manufacturing
Company's Standard Conditions of Sale. Published technical
data and instructions are subject to change without
prior notice.
50-Line(05/09)
LIMITED WARRANTY
The successful performance of this product is highly dependent on many factors beyond our control. Results are highly dependent upon the skill of the operator. This
product is manufactured to meet the highest level of consistency and quality for the intended use. Mobile Paint warrants that its products meet the specifications which it sets for
them. Should this product be proven to be off-specification within one year from date of shipment, Mobile Paint will, at its sole discretion, either replace the product or issue credit
for the original purchase price of the product. The replacement or refund shall be the buyer's sole remedy and Mobile Paint and its affiliates MAKE NO OTHER WARRANTY OR
GUARANTEE, EXPRESS OR IMPLIED, INCLUDING MERCHANTABILITY, DESIGN COMPATIBILITY AND FITNESS FOR A PARTICULAR PURPOSE. LABOR OR COST
OF LABOR AND OTHER INCIDENTAL AND/OR CONSEQUENTIAL DAMAGES ARE SPECIFICALLY EXCLUDED. The technical data contained herein are true and accurate
to the best of our knowledge. Published technical data and instructions are subject to change without prior notice.
